Dimmable Energy Star and CETL ETL Listed LED Panel Light LED Recessed Downlight Retrofit Bulb.

Product Detail

dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb description:


dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb

Widely applied in office lighting,hotel lighting,home lighting,commercial lighting.

 

dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb




DIMENSIONS:

· OD 9? (228 mm); ID 7 1/4? (185 mm); Thickness 2? (50 mm)

· Cut out: 8? +/- 1/2? (204 +/- 12 mm)

· Connection Box Dimensions (with driver inside): 5? (127 mm) x 3 5/16? (85 mm) x 1 1/8? (32 mm)

 

dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb

Character:

· Dimmable 

· cETLus Approved and Energy Star Certified

· Type IC Rated – Approved for Direct Contact with Insulation

· Air-Tight, Damp Location, Insulated and Non Insulated Ceilings

· Pot Light Housing is NOT Required even for Insulated Ceilings

· Warranty: 10 Year on Residential, 5 Year on Commercial Installations

 

dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb

Technical specification:
Cut hole in ceiling and snap fixture in opening with attached spring clips.
Space in ceiling needed – 2?.

· Default Driver Input Voltage: 120V AC 60 Hz (Dimmable)

· Optional Driver Input Voltage: 277V-347V AC 60 Hz (Not Dimmable)

· Power factor: 0.92

· Energy Used: 20W

· Halogen equivalent: 150W

· Beam Angle: 120°

· Light colour options: Warm White 3000°K and Neutral White 4100°K

· Light output: Warm White 2200 lm, Neutral White 2400 lm

· CRI: 84 for 3000°K and 82 for 4100°K

· Ambient Operating Temperature: -40°F (-40°C) to +104°F (+40°C)

· Compliance: cETLus, certified to CSA STD. C22.2 No. 250.0

· Rated: Type IC (Direct Contact with Insulation), Energy Star, Air-Tight

 

dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb




CONNECTING THE DRIVER:
Open the cover of the junction box. Push and remove one of the half-inch knockouts on the side plate. Install standard L16 cable connector. Use double connector for daisy chaining multiple drivers. Insert line voltage feed into the cable connector and splice same colour wires using wire nuts. Close the cover. Connect the driver to the light fixture – the arrows on the male and female parts of the connector between the driver and the fixture should match. Tighten the connector by hand. Do not attach the junction box to anything so you can pull it through the ceiling opening in case you need to service the driver in future.




dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb




OPTIONS FOR LOCATING DRIVER:

Fixture comes connected to the driver by 12? long low voltage cable with waterproof connector in the middle. Depending on where you want the driver to be you have 2 options:

· 1. Locate next to the fixture – run line voltage wiring to first junction box and “daisy chain” to the junction boxes of the other fixtures.

· 2. Or install all drivers at one location and use low voltage extension cables to the fixtures. Use only extensions provided by the manufacturer. Available jumper cables are 6 feet (1.8m) and 20 feet (6m). Cables are linkable. Maximum run should not exceed 40 feet (12m).

 

dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb




DIMMING:

We recommend LED/CFL dimmers that have a low range adjustment dial. After all fixtures are connected to the dimmer adjust the dial to the lowest position before the lights start to flicker of shut down. This setting depends on the local voltage and number of fixtures per dimmer.
For a typical LED dimmer rated for 150W LED load the maximum number of fixtures per dimmer is 3.

 

dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb

Choosing light color:

· Warm White 3000K is yellowish, similar to halogen and incandescent light. Creates soft, calming feeling. We recommend the Warm White for bedrooms, living rooms and kitchens with warm coloured countertops and cabinets.

· Neutral White 4100K is whiter, colder and more energizing light. Using this colour will make the room look white, modern and brighter. We recommend the Neutral White for bathrooms, offices and work areas, garages, kitchens with white or dark countertops and cabinets.

 

dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb




WARNING:
DO NOT USE ANY OTHER DRIVERS EXCEPT THE DANS DRIVERS THAT ARE INCLUDED WITH THE FIXTURE.
DO NOT CONNECT MULTIPLE FIXTURES TO ONE DRIVER.
DO NOT OPEN THE LIGHT FIXTURE AND THE SIDE PLATES OF THE DRIVER – NO SERVICEABLE PARTS INSIDE.




dimmable energy star and cETL ETL listed led panel light, led  recessed downlight retrofit bulb application: